[Title 46 CFR 110.10] [Code of Federal Regulations (annual edition) - October 1, 1996 Edition] [Title 46 - SHIPPING] [Chapter I - COAST GUARD, DEPARTMENT OF] [Subchapter J - ELECTRICAL ENGINEERING] [Part 110 - GENERAL PROVISIONS] [Subpart 110.10 - Reference Specifications, Standards, and Codes] [From the U.S. Government Publishing Office]46 SHIPPING 4 1996-10-01 1996-10-01 false Reference Specifications, Standards, and Codes 110.10 Subpart 110.10 SHIPPING COAST GUARD, DEPARTMENT OF ELECTRICAL ENGINEERING GENERAL PROVISIONS Subpart 110.10--Reference Specifications, Standards, and Codes Sec. 110.10-1 Incorporation by reference. (a) Certain material is incorporated by reference into this subchapter with the approval of the Director of the Federal Register under 5 U.S.C. 552(a) and 1 CFR part 51. To enforce any edition other than that specified in paragraph (b) of this section, the Coast Guard must publish notice of change in the Federal Register; and the material must be available to the public. All approved material is available for inspection at the Office of the Federal Register, 800 North Capitol Street NW., suite 700, Washington, DC, and at the U.S. Coast Guard, (G- MSE), 2100 Second Street SW., Washington, DC 20593-0001, and is available from the sources indicated in paragraph (b) of this section. (b) The material approved for incorporation by reference in this subchapter and the sections affected are as follows: American Bureau of Shipping (ABS) American Bureau of Shipping, Two World Trade Center, 106th Floor, New York, NY 10048: Rules for Building and Classing Steel 110.15-1; 111.12-1(a); Vessels, 1995. 111.12-3; 111.12-5; 111.12-7; 111.33-11; 111.35-1; 111.70-1(a); 111.105-31(n); 111.105- 39(a); 111.105-40(a); 113.05-7. Rules for Building and Classing Mobile 111.12-1(a); 111.12-3; Offshore Drilling Units, 1994. 111.12-5; 111.12-7; 111.33-11; 111.35-1; 111.70-1(a). American National Standards Institute (ANSI), American National Standards Institute, 11 West 42nd Street, New York, NY 10036: ANSI/ASME A17.1, Safety Code for 111.91-1 Elevators and Escalators, 1993. ANSI/ASME A17.1A, Addenda to ANSI/ASME 111.91-1. A17.1, Safety Code for Elevators and Escalators (including Errata, 1995), 1994. ANSI/IEEE C37.04, Rating Structure for AC 111.54-1(c). High-Voltage Circuit Breakers Rated on a Symmetrical Current Basis, 1979. ANSI C37.12, For AC High-Voltage Circuit 111.54-1(c). Breakers Rated on a Symmetrical Current Basis--Specification Guide, 1991. American Society for Testing and Materials (ASTM), ASTM International Headquarters, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959: ASTM B 117-95, Standard Practice for 110.15-1(b). Operating Salt Spray (Fog) Apparatus, 1996. ASTM D 4066-94b, Standard Specification 111.60-1(c) for Nylon Injection and Extrusion Materials (PA), 1994. Institute of Electrical and Electronic Engineers (IEEE), IEEE Service Center, 445 Hoes Lane, Piscataway, NJ 08854: [[Page 212]] IEEE Std C37.13, IEEE Standard for Low- 111.54-1(c). Voltage AC Power Circuit Breakers used in Enclosures, 1990. IEEE Std C37.14, IEEE Standard for Low- 111.54-1(c). Voltage DC Power Circuit Breakers Used in Enclosures, 1992. IEEE Std 45-1983, IEEE Recommended 111.05-7; 111.15-2(b); Practice for Electric Installations on 111.30-1; 111.30-5(a); Shipboard, 1983. 111.30-19(a); 111.33- 3(a); 111.33-5(a); 111.60-1(a); 111.60-2; 111.60-3; 111.60-5(a); 111.60-6(a); 111.60- 11(c); 111.60-13(a); 111.60-19(b); 111.60-21; 111.60-23(d); 111.105-3; 111.105-31(e); 111.105- 41; 111.107-1(c); 113-65- 5. IEEE Std 100-1992, The New IEEE Standard 110.15-1(a). Dictionary of Electrical and Electronics Terms, 1992. IEEE Std 320, Application Guide for AC 111.54-1(c). High-Voltage Circuit Breakers Rated on a Symmetrical Current Basis (ANSI/IEEE C37.010-79), 1979. IEEE Std 331, Application Guide for Low- 111.54-1(c). Voltage AC Nonintegrally Fused Power Circuit Breakers (Using Separately Mounted Current-Limiting Fuses) (ANSI/ IEEE C37.27), 1987. IEEE Std 1202-1991, IEEE Standard for 111.60-2; 111.60-6(a); Flame Testing of Cables for Use in Cable 111.107-1(c). Tray in Industrial and Commercial Occupancies, 1991. International Association of Drilling Contractors (IADC), International Association of Drilling Contractors, PO Box 4287, Houston, TX 77210-4287: IADC-DCCS-1/1991, Guidelines for 111.60-1(f). Industrial System DC Cable for Mobile Offshore Drilling Units, 1991. International Electrotechnical Commission (IEC), (Also available from ANSI--address above.) International Electrotechnical Commission, 1, Rue de Varembe, Geneva, Switzerland: IEC 68-2-52, Basic Environmental Testing 110.15-1(b). Procedures, Part 2: Tests. Test KB: Salt Mist, Cyclic (Sodium Chloride Solution), 1984. IEC 79-0, Electrical Apparatus for 111.105-1; 111.105-3; Explosive Gas Atmospheres, Part 0: 111.105-5; 111.105-7; General Requirements, 1983 (Including 111.105-15(b); 111.105- Amendment 2, 1991). 17(b). IEC 79-1, Electrical Apparatus for 111.105-3; 111.105-5; Explosive Gas Atmospheres, Part 1: 111.105-9; 111.105- Construction and Test of Flameproof 15(b); 111.105-17(b). Enclosures of Electrical Apparatus, 1990 [Including the First Supplement to the Second Edition (1971), 1975, and Amendment 1 to the Third Edition (1990), 1993]. IEC 79-2, Electrical Apparatus for 111.105-3; 111.105-5; Explosive Gas Atmospheres, Part 2: 111.105-7(b); 111.105- Electrical Apparatus--Type of Protection 15(b); 111.105-17(b). ``p'', 1983. IEC 79-5, Electrical Apparatus for 111.105-3; 111.105-5; Explosive Gas Atmospheres, Part 5: Sand- 111.105-15(a); 111.105- Filled Apparatus. First Edition (1967), 15(b); 111.105-17(b). Incorporating the First Supplement, (1969). IEC 79-6, Electrical Apparatus for 111.105-3; 111.105-5; Explosive Gas Atmospheres, Part 6: Oil- 111.105-15(a); 111.105- Immersion ``o'', 1995. 15(b); 111.105-17(b). IEC 79-7, Electrical Apparatus for 111.105-3; 111.105-5; Explosive Gas Atmospheres, Part 7: 111.105-15(a); 111.105- Increased Safety ``e'', 1990 (Including 15(b); 111.105-17(b). Amendment 1, 1991, and Amendment 2 1993). IEC 79-11, Electrical Apparatus for 111.105-3; 111.105-5; Explosive Gas Atmospheres, Part 11: 111.105-11(a); 111.105- Intrinsic Safety ``i'', 1991. 15(b); 111.105-17(b). IEC 79-15, Electrical Apparatus for 111.105-3; 111.105-5; Explosive Gas Atmospheres, Part 15: 111.105-15(a); 111.105- Electrical Apparatus with Type of 5(b); 111.105-17(b). Protection ``n'', 1987. IEC 79-18, Electrical Apparatus for 111.105-3; 111.105-5; Explosive Gas Atmospheres, Part 18: 111.105-15(a); 111.105- Encapsulation ``m'', 1992. 15(b); 111.105-17(b). [[Page 213]] IEC 92-3, Electrical Installation in 111.05-7; 111.60-1(a); Ships, Part 3: Cables (construction, 111.60-3(a); 111.60- testing and installations) Second 3(c); 111.81-1(d). Edition, 1965, as amended through August, 1982. IEC 92-101, Electrical Installations in 110.15-1(a); 111.81-1(d). Ships, Part 101: Definitions and General Requirements, 1994 (Including Amendment 1, 1995). IEC 92-201, Electrical Installations in 111.70-3(a); 111.81-1(d). Ships, Part 201: System Design--General 1994. IEC 92-202, Electrical Installations in 111.50-3(c); 111.50-3(e); Ships, Part 202: System Design-- 111.50-3(g); 111.53- Protection, 1994. 1(a); 111.54-1(a); 111.81-1(d). IEC 92-301, Electrical Installations in 111.25-5(a); 111.70-1(a); Ships, Part 301: Equipment--Generators 111.81-1(d). and Motors, 1980 (Including Amendment 1, 1994, and Amendment 2, 1995). IEC 92-302, Electrical Installations in 111.30-1; 111.30-5(a); Ships, Part 302: Equipment--Switchgear 111.30-19(a); 111.81- and Controlgear Assemblies, 1980 1(d). (Including Amendment 1, 1989, and Amendment 2, 1994). IEC 92-303, Electrical Installations in 111.20-15; 111.81-1(d). Ships, Part 303: Equipment--Transformers for Power and Lighting, 1980. IEC 92-304, Electrical Installations in 111.33-3(a); 111.33-5(b); Ships, Part 304: Equipment-- 111.81-1(d). Semiconductor Converters, 1980 (Including Amendment 1, 1995). IEC 92-306, Electrical Installations in 111.75-20(a); 111.81- Ships, Part 306: Equipment--Luminaires 1(d). and Accessories, 1980. IEC 92-352, Electrical Installations in 111.60-3(a); 111.60-3(c); Ships, Part 352: Choice and Installation 111.60-5; 111.81-1(d). of Cables for Low-Voltage Power Systems, 1979, (Including Amendment 1, 1987, and Amendment 2, 1994). IEC 92-501, Electrical Installations in 111.81-1(d). Ships, Part 501: Special Features-- Electric Propulsion Plant, 1984. IEC 92-502, Electrical Installations in 111.81-1(d); 111.105- Ships, Part 502: Tankers--Special 31(e). Features, 1994. IEC 92-503, Electrical Installations in 111.30-5(a); 111.81-1(d). Ships, Part 503: Special Features--A.C. Supply systems with Voltages in the Range Above 1KV up to and including 11KV, 1975. IEC 92-504, Electrical Installations in 111.81-1(d). Ships, Part 504: Special Features-- Control and Instrumentation, 1994. IEC 331, Fire resisting characteristics 113.30-25(i). of electric cables, 1970. IEC 332-1, Tests on Electric Cables Under 111.30-19(b). Fire Conditions, Part 1: Test on a Single Vertical Insulated Wire or Cable, 1993. IEC 332-3, Tests on Electric Cables Under 111.60-1(b); 111.60-2; Fire Conditions, Part 3: Test on bunched 111.60-6(a); 111.107- wires or cables, 1992. 1(c). IEC 363, Short-Circuit Current Evaluation 111.52-5(c). with Special Regard to Rated Short- Circuit Capacity of Circuit-Breakers in Installations in Ships, 1972. IEC 529, Degrees of protection provided 111.01-9(a); 111.01-9(b); by enclosures (IP Code) 1989. 111.01-9(c); 111.01- 9(d); 111.01-9 (Note); 113.10-7; 113.20-3; 113.25-11; 113.30-25(c); 113.30-25(h); 113.40- 10(b). IEC 533, Electromagnetic Compatibility of 113.05-7. Electrical and Electronic Installations in Ships, 1977. IEC 947-2, Low-Voltage Switchgear and 111.54-1(b); 111.54-1(c). Controlgear, Part 2: Circuit Breakers, 1989 (Including Amendment 1, 1992 and Amendment 2, 1993). IEC IP Code, see IEC 529. International Maritime Organization (IMO), International Maritime Organization, 4 Albert Embankment, London SE1 7SR, England: International Convention for the Safety 111.99-5; 111.105-31(n); of Life at Sea, 1974 (SOLAS 74) 112.15-1(r); 113.25-6. Consolidated Edition, (Including 1992 Amendments to SOLAS 74, and 1994 Amendments to SOLAS 74), 1992. [[Page 214]] The International Society for Measurement and Control (ISA), International Society for Measurement and Control, 67 Alexander Drive. P.O. Box 12277 Research Triangle Park, NC 27709: RP 12.6, Wiring Practices for Hazardous 111.105-11(e). (Classified) Locations Instrumentation Part I: Intrinsic Safety, 1995. National Electrical Manufacturers Association (NEMA), National Electrical Manufacturers Association, 2101 L Street, NW, Washington, DC 20036: NEMA Standards Publication No. ICS 2, 111.70-3(a). Industrial Control and Systems Controllers, Contractors, and Overload Relays Rated not more than 2000 Volts AC or 750 Volts DC, 1993. NEMA Standards Publication No. 2.3 1983, 111.70-3(a). Instructions for the Handling, Installation, Operation, and Maintenance of Motor Control Centers, 1983. NEMA Standards Publication No. 2.4, NEMA 111.70-3(a). and IEC Devices for Motor Service--A Guide for Understanding the Differences, 1989. NEMA Standards Publication No. 250, 111.01-9(a); 111.01-9(b); Enclosures for Electrical Equipment 111.01-9(c); 111.01- (1000 Volts Maximum), 1991. 9(d); 111.01-9 (Note); 111.10-7; 113.20-3; 113.25-11; 113.30-25(c); 113.30-25(h); 113.40- 10(b). NEMA Standards Publication No. WC-3, 111.60-13(a); 111.60- Rubber Insulated Wire and Cable for the 13(c). Transmission and Distribution of Electrical Energy, 1980 (with revisions through May 1989). NEMA Standards Publication No. WC-8, 111.60-13(a); 111.60- Ethylene-Propylene-Rubber-Insulated Wire 13(c). and Cable for the Transmission and Distribution of Electrical Energy, 1988 (with revisions through 1992). National Fire Protection Association (NFPA), National Fire Protection Association, 1 Batterymarch Park, Quincy, MA 02269: NEC, see NFPA 70......................... NFPA 70, National Electrical Code (NEC), 111.05-33; 111.20-15; 1996. 111.25-5(a); 111.50- 3(c); 111.50-7; 111.50- 9; 111.53-1(a); 111.54- 1(a); 111.55-1(a); 111.59-1; Table 111.60- 7; 111.60-11(f); 111.60- 13(a); 111.60-13(b); 111.60-13(c); 111.60-23; 111.81-1(d); 111.83- 3(a); 111.105-1; 111.105- 1 (Note); 111.105-3; 111.105-5; 111.105-7; 111.105-9; 111.105- 15(a); 111.105-17(b); 111.107-1(b). NFPA 77, Recommended Practice on Static 111.105-27. Electricity, 1993. NFPA 99, Standard for Health Care 111.105-37. Facilities, 1996. NFPA 496, Standard for Purged and 111.105-7(b). Pressurized Enclosures for Electrical Equipment, 1993. Naval Publications and Forms Center (NPFC), Naval Publications and Forms Center, Customer Service--Code 1052, 5801 Tabor Avenue Philadelphia, PA 19120: MIL-W-76D, Military Specification Wire 111.60-11(c). and Cable, Hook-up, Electrical, Insulated, General Specification For, 1992. MIL-W-16878F, Military Specification, 111.60-11(c). Wire, Electrical, Insulated, General Specification For, 1992. MIL-C-24640A, Military Specification 111.60-1(a); 111.60-3(c). Cables, Light Weight, Electric, Low Smoke, For Shipboard Use, General Specification For, 1995. [[Page 215]] MIL-C-24643A, Military Specification 111.60-1(a); 111.60-3(c). Cables and Cords, Electric, Low Smoke, For Shipboard Use, General Specification For, 1994 (Including Amendment 1). Naval Sea Systems Command (NAVSEA), Naval Sea Systems Command, Code 55Z, Department of Navy Washington, DC 20362: DDS 300-2, A. C. Fault Current 111.52-5. Calculations, 1988. MIL-HDBK-299 (SH), Military Handbook 111.60-3(c). Cable Comparison Handbook Data Pertaining to Electric Shipboard Cable, 1989. Underwriters Laboratories Inc. (UL), Underwriters Laboratories, Inc., ATTN: Publications Stock, 333 Pfingsten Rd. Northbrook, IL 60062-2096: UL 44, Standard for Rubber-Insulated Wire 111.60-11(c). and Cable, 1991 (including revisions through February, 1996). UL 50, Standard for Enclosures for 111.81-1(d). Electrical Equipment, 1995. UL 62, Standard for Flexible Cord and 111.60-13(a). Fixture Wire, 1991 (including revisions through February, 1996). UL 83, Standard for Thermoplastic- 111.60-1(c); 111.60- Insulated Wires and Cables, 1991 11(c). (including revisions through March, 1996). UL 489, Standard for Molded-Case Circuit 111.54-1(b). Breakers and Circuit-Breaker Enclosures, 1991 (including revisions through June, 1995). UL 514A, Standard for Metallic Outlet 111.81-1(d). Boxes, 1991 (including revisions through April, 1995). UL 514B, Standard for Fittings for 111.81-1(d). Conduit and Outlet Boxes, 1989 (including revisions through April, 1995). UL 514C, Standard for Nonmetallic Outlet 111.81-1(d). Boxes, Flush-Device Boxes, and Covers, 1988 (including revisions through April, 1995). UL 595, Standard for Marine-Type Electric 111.75-20(a); 111.75- Lighting Fixtures, 1985 (including 20(e). revisions through September, 1991). UL 913, Standard for Intrinsically Safe 111.105-11(a). Apparatus and Associated Apparatus for Use in Class I, II, and III Division 1, Hazardous (Classified) Locations, 1988. UL 1042, Standard for Electric Baseboard 111.87-3(a). Heating Equipment, 1994 (including revisions through November, 1995). UL 1072, Standard for Medium-Voltage 111.60-1(e). Power Cables, 1995 (including revisions through January, 1996). UL 1096, Standard for Electric Central 111.87-3(a). Air Heating Equipment, 1986 (including revisions through January, 1988). UL 1104, Standard for Marine Navigation 111.75-17(d). Lights, 1981 (including revisions through May, 1988). UL 1203, Standard for Explosion-Proof and 111.105-9. Dust-Ignition-Proof Electrical Equipment for Use in Hazardous (Classified) Locations, 1994 (including revisions through October, 1995). UL 1569, Standard for Metal-Clad Cables, 111.60-23(a). 1995 (including revisions through April, 1996). UL 1570, Standard for Fluorescent 111.75-20. Lighting Fixtures, 1988 (including revisions through April, 1996). UL 1571, Standard for Incandescent 111.75-20. Lighting Fixtures, 1995 (including revisions through April, 1996). UL 1572, Standard for High Intensity 111.75-20. Discharge Lighting Fixtures, 1995 (including revisions through May, 1996). UL 1573, Standard for Stage and Studio 111.75-20. Lighting Units, 1994 (including revisions through February, 1995). UL 1574, Standard for Track Lighting 111.75-20. Systems, 1995 (including revisions through July, 1995). ANSI/UL 1581, Reference Standard for 111.30-19(b); 111.60-2; Electrical Wires, Cables, and Flexible 111.60-6(a). Cords, 1991 (including revisions through January, 1996). [[Page 216]] (c) The word ``should,'' when used in material incorporated by reference, is to be construed the same as the words ``must'' or ``shall'' for the purposes of this subchapter. [CGD 94-108, 61 FR 28271, June 4, 1996; 61 FR 33045, June 26, 1996; 61 FR 36786-36787, July 12, 1996; 61 FR 49691, Sept. 23, 1996]